発電機ワイヤー サイズ計算ツール
// KW、電圧、距離、電圧降下目標から、発電機インレット、切替スイッチ、非常用配電配線のフィーダー導体サイズを選定 //
導体の概算選定用に、発電機銘板の有効電力出力をキロワット単位で入力してください。
実際の発電機出力またはフィーダ電圧を選択して、電流と電圧降下が適切にチェックされるようにします。
抵抗またはネームプレートの kW 計画には 1.00 を使用するか、発電機の負荷がモーターの負荷が大きい場合には、より低い PF を入力します。
発電機の電源と接続された機器の間の片道導体の長さをフィート単位で入力します。
ストレートな銘板チェックではなく、持続的な発電機負荷のための 125% 計画画面が必要な場合は、これを有効にします。
12 kW at 240 V, single-phase, PF 1.00
115% minimum generator-output conductor screen per NEC 445.13.
21.1 mm² equivalent, 70.0 A ampacity screen, 2.31 V estimated drop (0.96%).
各行で、選択した導体材質と端子温度定格について、入力した配線距離での必要許容電流と推定電圧降下の両方を確認します。
| サイズ | 許容電流 | 抵抗 | 電圧降下 | 状態 |
|---|---|---|---|---|
14 AWG 2.1 mm² | 15.0 A | 3.0700 ohm/kft | 23.0 V / 9.59% | サイズアップ |
12 AWG 3.3 mm² | 20.0 A | 1.9300 ohm/kft | 14.5 V / 6.03% | サイズアップ |
10 AWG 5.3 mm² | 30.0 A | 1.2100 ohm/kft | 9.07 V / 3.78% | サイズアップ |
8 AWG 8.4 mm² | 40.0 A | 0.7640 ohm/kft | 5.73 V / 2.39% | サイズアップ |
6 AWG 13.3 mm² | 55.0 A | 0.4910 ohm/kft | 3.68 V / 1.53% | サイズアップ |
4 AWG 21.1 mm² | 70.0 A | 0.3080 ohm/kft | 2.31 V / 0.96% | 適合 |
3 AWG 26.7 mm² | 85.0 A | 0.2450 ohm/kft | 1.84 V / 0.77% | 適合 |
2 AWG 33.6 mm² | 95.0 A | 0.1940 ohm/kft | 1.46 V / 0.61% | 適合 |
1 AWG 42.4 mm² | 110 A | 0.1540 ohm/kft | 1.16 V / 0.48% | 適合 |
1/0 AWG 53.5 mm² | 125 A | 0.1220 ohm/kft | 0.91 V / 0.38% | 適合 |
2/0 AWG 67.4 mm² | 145 A | 0.0967 ohm/kft | 0.73 V / 0.30% | 適合 |
3/0 AWG 85.0 mm² | 165 A | 0.0766 ohm/kft | 0.57 V / 0.24% | 適合 |
4/0 AWG 107.2 mm² | 195 A | 0.0608 ohm/kft | 0.46 V / 0.19% | 適合 |
250 kcmil 126.7 mm² | 215 A | 0.0515 ohm/kft | 0.39 V / 0.16% | 適合 |
300 kcmil 152.0 mm² | 240 A | 0.0429 ohm/kft | 0.32 V / 0.13% | 適合 |
350 kcmil 177.3 mm² | 260 A | 0.0367 ohm/kft | 0.28 V / 0.11% | 適合 |
400 kcmil 202.7 mm² | 280 A | 0.0321 ohm/kft | 0.24 V / 0.10% | 適合 |
500 kcmil 253.3 mm² | 320 A | 0.0258 ohm/kft | 0.19 V / 0.08% | 適合 |
Use this calculator for fixed wiring between a generator, inlet, transfer switch, disconnect, or downstream distribution equipment. If you are sizing a portable cord set instead, use the extension cord tool and verify the cord listing.
- 発電機のフィーダー導体については、過電流保護、転送機器のリスト、および設置に適用される中性点または接地の規則について、最終的な確認がまだ必要です。
- ここでの電圧降下制限は計画目標であり、NEC の直接の義務ではありません。敏感な機器やモーターの始動では、多くの場合、より厳しい落下制限が必要になります。
- このツールは、発電機と下流の機器の間の固定配線用であり、柔軟なポータブル コード セットや一時的な配線の承認用ではありません。
7.5 kW portable generator to 30A inlet
At 240 V single-phase and 60 ft one way, the calculated current is about 31.3 A. 10 AWG copper has enough ampacity but usually pushes above a tight 2% drop limit, so 8 AWG becomes the cleaner fixed-wiring choice.
20 kW standby generator to transfer switch
A 20 kW, 120/240 V single-phase unit delivers about 83.3 A at PF 1.00. With a 100 ft run and 3% target, 3 AWG copper can be a practical planning result before final OCPD, neutral sizing, and grounding checks.
60 kW three-phase generator feeder
On 480 V three-phase at PF 0.9, load current is roughly 80 A. Voltage drop is modest at this voltage, so the selection is often driven by ampacity, terminals, and installation conditions rather than distance alone.
Voltage Drop Calculator
Run a broader AC voltage-drop check after the generator circuit layout is known.
Ampacity Calculator
Review terminal temperature, bundling, and derating before final conductor release.
Conduit Fill Calculator
Check raceway occupancy once phase, neutral, and grounding conductors are selected.
Cable Size Calculator
Compare the generator feeder result with a broader residential or commercial sizing workflow.
Wire Resistance Calculator
Audit raw conductor resistance if you want to inspect the voltage-drop math directly.
Wire Weight Calculator
Estimate pull weight and reel handling for larger standby generator feeders.