Расчет заполнения коробки — один из самых часто пропускаемых расчетов в жилых и лёгких коммерческих электромонтажных работах. Допустимый ток и падение напряжения замечают раньше, а переполненные коробки обнаруживают только при монтаже или проверке.
Данное руководство объясняет, как правильно подсчитывать проводники, устройства, заземление и зажимы для верного подбора размера коробки.
Code References
Cet article fait référence aux articles NEC 314.16(A), 314.16(B) et 314.16(C) concernant le volume de boîte et les allocations des conducteurs.
Pourquoi le remplissage de boîte est important
Le NEC exige un volume libre suffisant pour chaque conducteur et dispositif dans une boîte. Cet espace est nécessaire pour le pliage des conducteurs, la dissipation thermique et la maintenance future.
Le NEC fournit une méthode de comptage reproductible basée sur le calibre du conducteur et l'équipement dans le boîtier.
Si le comptage 12 AWG atteint 9 allocations, je vérifie au moins 20,25 pouces cubiques sur l'étiquette avant de commencer la finition. — Hommer Zhao, Technical Director
Formule NEC de remplissage de boîte
Volume requis = nombre total d'allocations × allocation en pouces cubiques du plus gros conducteur
La difficulté n'est pas la multiplication mais le comptage correct. Selon le câblage, il faut ajouter des allocations pour les terres, les pinces internes et les dispositifs.
Allocations de volume par conducteur
NEC 314.16(B) attribue une allocation en pouces cubiques à chaque calibre de conducteur.
| Conductor Size | Volume Allowance | Typical Use |
|---|---|---|
| 18 AWG | 1.50 cu in | Class 1 and fixture wiring |
| 16 AWG | 1.75 cu in | Limited control circuits |
| 14 AWG | 2.00 cu in | 15A lighting and receptacle circuits |
| 12 AWG | 2.25 cu in | 20A branch circuits |
| 10 AWG | 2.50 cu in | 30A equipment circuits |
| 8 AWG | 3.00 cu in | Feeders and heavy loads |
| 6 AWG | 5.00 cu in | Large feeders and service work |
Ce qui compte comme une allocation
Chaque conducteur isolé venant de l'extérieur et se terminant ou traversant la boîte compte comme une allocation.
- Chaque conducteur isolé entrant dans la boîte compte une fois.
- Toutes les terres d'équipement comptent ensemble comme un seul conducteur du plus gros calibre de terre.
- Les pinces internes comptent comme un conducteur du plus gros calibre dans la boîte.
- Chaque bride de dispositif avec interrupteur ou prise compte comme deux allocations.
- Les queues de cochon internes ne comptent pas dans le remplissage.
Common Misread
Une prise double sur une bride reste deux allocations, pas une. Les erreurs de comptage de dispositifs sont très courantes.
Les terres sont le piège de l'optimisme. Six fils de terre nus dans une boîte plastique ne comptent qu'une allocation, mais ça ne signifie pas qu'il y a de la place pour tout. — Hommer Zhao, Technical Director
Méthode de comptage étape par étape
- Lire le marquage de la boîte et confirmer sa capacité en pouces cubiques.
- Lister tous les conducteurs isolés entrant ou traversant la boîte.
- Ajouter une allocation pour toutes les terres combinées.
- Ajouter une allocation pour les pinces internes si présentes.
- Ajouter deux allocations par bride de dispositif.
- Multiplier le total par l'allocation du plus gros conducteur.
- Comparer le volume requis au volume de la boîte.
Exemples chiffrés
Les exemples suivants reflètent des boîtes résidentielles et commerciales courantes.
Exemple 1 : Interrupteur unipolaire, 14 AWG
Deux câbles 14/2 NM : 4 conducteurs isolés + 1 terre + 2 bride = 7 allocations. À 2,00 pouces cubiques, minimum 14,0 pouces cubiques.
Exemple 2 : GFCI 20A, 12 AWG, pince interne
Deux câbles 12/2 : 4 conducteurs + 1 terre + 1 pince + 2 bride = 8 allocations. Minimum 18,0 pouces cubiques.
Exemple 3 : Interrupteur 3 voies, 14/3 + 14/2
5 conducteurs isolés + 1 terre + 2 bride = 8 allocations. Minimum 16,0 pouces cubiques.
Exemple 4 : Boîte 2 postes, 2 interrupteurs
Trois câbles 12/2 : 6 conducteurs + 1 terre + 4 brides = 11 allocations. Minimum 24,75 pouces cubiques.
Exemple 5 : Boîte de jonction seule
4 conducteurs 10 AWG + 1 terre = 5 allocations. Minimum 12,5 pouces cubiques.
Quand une boîte 2 postes dépasse 10 allocations en 12 AWG, je spécifie directement la boîte plus grande. — Hommer Zhao, Technical Director
Remplissage de boîte vs remplissage de conduit
Le remplissage de conduit utilise la section et les pourcentages du chapitre 9 NEC. Le remplissage de boîte utilise le volume en pouces cubiques du NEC 314.16.
Erreurs fréquentes
- Ignorer les allocations de bride de dispositif.
- Oublier les pinces internes, surtout dans les boîtes métalliques.
- Confondre queues de cochon et conducteurs traversants.
- Utiliser une boîte peu profonde sur un circuit 12 AWG cuisine.
- Supposer que les bagues d'extension résolvent tous les problèmes.
- Confondre remplissage de boîte avec ampacité ou chute de tension.
Practical Rule
Si le calcul passe de justesse et que la boîte contiendra un GFCI ou un variateur, choisissez la boîte plus grande.
Conseils pour ingénieurs et bricoleurs
Les ingénieurs doivent vérifier le remplissage dès la conception, pas au montage.
Si vous vérifiez déjà la taille du conducteur, vérifiez aussi la taille de la boîte.
FAQ
Chaque fil de terre compte-t-il ?
Non. Toutes les terres comptent comme une seule allocation du plus gros calibre.
Combien d'allocations pour une prise ?
Deux allocations par bride.
Les queues de cochon comptent-elles ?
Non, si elles commencent et finissent dans la même boîte.
Quelle taille de boîte pour 2 câbles 12/2 et un interrupteur ?
7 allocations. À 2,25 pouces cubiques, minimum 15,75. Avec pince interne : 18,0.
Une bague d'extension augmente-t-elle le volume légal ?
Oui, si elle est certifiée avec un volume marqué.
Le remplissage de boîte s'applique-t-il en norme IEC ?
La règle exacte dépend du code local, mais le principe est le même.
Conclusion
Le remplissage de boîte est simple avec une checklist : compter les conducteurs, ajouter terres, pinces, brides, multiplier par l'allocation correcte.
Pour vérifier taille de conducteur, capacité de conduit ou chute de tension, commencez par nos calculateurs. Contact us
Руководство по расчету заполнения электрических коробок: Field Verification Table
Before you close out руководство по расчету заполнения электрических коробок, it helps to cross-check the same five items that inspectors and experienced installers review in the field: load basis, breaker protection, voltage drop, derating, and grounding or enclosure space. The underlying logic is consistent across the National Electrical Code and the International Electrotechnical Commission: use the actual load, verify the conductor against installation conditions, and only then lock in protection and layout details.
| Design Check | What to Verify | Practical Number | Typical Code Reference | Best Tool or Follow-Up |
|---|---|---|---|---|
| Load Basis | Start from nameplate load, calculated load, or connected VA before picking a conductor. | Continuous loads are usually checked at 125%. | NEC 210.19(A)(1) and 215.2(A)(1) | Use the main wire gauge calculator for the first pass. |
| Breaker Match | Protect the conductor ampacity instead of assuming the breaker sets wire size by itself. | 16A continuous becomes a 20A conductor check. | NEC 240.4 and 240.6(A) | Compare against the breaker sizing guide before trim-out. |
| Voltage Drop | Long runs often require larger wire even when ampacity already passes. | Design target is about 3% branch and 5% feeder plus branch. | NEC informational notes to 210.19 and 215.2 | Run a second check in the voltage drop calculator. |
| Derating | Account for ambient temperature, rooftop heat, and more than three current-carrying conductors. | 90 C insulation may still terminate on a 75 C or 60 C limit. | NEC 310.15 and Table 310.16 | Confirm with the ampacity calculator before ordering wire. |
| Grounding and Fill | Check equipment grounds, conduit fill, and box space as separate calculations. | A 60A feeder often uses a 10 AWG copper EGC under NEC 250.122. | NEC 250.122, 314.16, and Chapter 9 | Cross-check the ground wire and conduit fill guides before inspection. |
“If a circuit will run for 3 hours or more, I treat the 125% continuous-load check as non-negotiable. A 16A design current turning into a 20A conductor decision is exactly the kind of detail that prevents nuisance heat and callbacks.”
“Once branch-circuit voltage drop gets close to 3%, I stop debating and price the next conductor size. Moving from 12 AWG to 10 AWG on a 120V run is usually cheaper than troubleshooting low-voltage performance later.”
“The breaker, phase conductor, and equipment ground are related, but they are not the same calculation. I may upsize a 60A feeder to 4 AWG copper for distance and still keep the grounding conductor at 10 AWG copper because NEC 250.122 keys it to the overcurrent device.”
How to Use This With the Calculator
The calculator gives you a fast starting point, but serious installations still need one more pass for voltage drop, conductor temperature rating, and code-specific exceptions. That last review is where most inspection problems get removed before material is pulled.
Руководство по расчету заполнения электрических коробок: Practical Number Checks
The easiest way to keep руководство по расчету заполнения электрических коробок practical is to sanity-check a few common field numbers before you order wire or close walls. On a 120V branch circuit carrying a 16A continuous load, the 125% rule pushes the conductor check to 20A. That is why 12 AWG copper becomes the real starting point instead of 14 AWG, even before you think about distance. If that same run stretches to 110 feet one way, voltage drop often pushes the design to 10 AWG while the breaker stays at 20A because the load has not changed.
The same logic shows up in larger work. A 7.5 HP, 460V three-phase motor with a full-load current around 11A does not mean you can stop at an 11A wire decision. Motor circuits, feeder calculations, and equipment grounding all apply their own code logic, and the conductor selected from ampacity tables still has to survive ambient temperature, rooftop heat, or bundling. That is why experienced electricians compare the load calculation against conductor ampacity, then against raceway or box space, and only then against the final breaker or fuse size.
Residential work needs the same discipline. A box-fill calculation that lands at 24.75 cubic inches on a 12 AWG two-gang box, or a detached garage feeder that picks up 3.6V of drop on a 120V leg, is already telling you the installation is too close to the edge. Use the long-distance wire guide when length is the problem, and cross-check enclosure constraints with the box fill guide or the conduit fill guide. Those second-pass checks are where most field rework gets avoided.
Руководство по расчету заполнения электрических коробок: Frequently Asked Questions
How do I know when руководство по расчету заполнения электрических коробок needs a larger conductor than a simple chart shows?
If the run is long, the load is continuous for 3 hours or more, or the conductors are bundled in hot ambient conditions, the simple chart is only the starting point. A 20A circuit may still need 10 AWG instead of 12 AWG once the 125% rule or a 3% voltage-drop target is applied.
Does the 125% continuous-load rule matter for руководство по расчету заполнения электрических коробок?
Yes, whenever the load is expected to run at maximum current for 3 hours or more. Under NEC 210.19(A)(1) and 215.2(A)(1), a 24A continuous load is treated as 30A for conductor sizing, which is why field calculations often move up one breaker and wire size from the first rough estimate.
What voltage-drop target is practical when planning руководство по расчету заполнения электрических коробок?
The common design target is about 3% on a branch circuit and 5% total for feeder plus branch circuit. That is not a mandatory blanket rule in every NEC application, but it is the benchmark many electricians use to decide when a 100-foot to 200-foot run should be upsized.
Can I upsize wire without increasing breaker size for руководство по расчету заполнения электрических коробок?
Yes. Upsizing for voltage drop or future durability does not automatically require a larger breaker. A common example is a 20A circuit that moves from 12 AWG to 10 AWG copper on a long run while the breaker remains 20A because the load and overcurrent protection have not changed.
Which code checks should I finish before calling руководство по расчету заполнения электрических коробок complete?
At minimum, verify conductor ampacity in NEC Table 310.16, breaker protection in NEC 240.4 and 240.6, voltage drop design assumptions, grounding in NEC 250.122, and enclosure or raceway space in NEC 314.16 or Chapter 9. For international work, align the same review with IEC-style conductor and protection practices.
Next Steps
If you want to validate this topic against real project numbers, start with the wire gauge calculator, then cross-check longer runs in the voltage drop calculator, and verify conductor adjustments with the ampacity calculator. If you want us to add another worked example or application note, contact us here.