Calculateur de section de fil pour génératrice
// ÉVALUEZ LA SECTION DES CONDUCTEURS D'ARTÈRE POUR LES PRISES DE GÉNÉRATRICE, LES COMMUTATEURS DE TRANSFERT ET LES PARCOURS DE DISTRIBUTION DE SECOURS À PARTIR DES KW, DE LA TENSION, DE LA DISTANCE ET DE LA CIBLE DE CHUTE DE TENSION //
Entrez la puissance active nominale de la génératrice en kilowatts pour une première évaluation de la section des conducteurs.
Choisissez la tension réelle de sortie de la génératrice ou de l'artère afin que le courant et la chute de tension soient vérifiés sur la bonne base.
Utilisez 1.00 pour une charge résistive ou une planification selon les kW de la plaque signalétique, ou entrez un facteur de puissance plus faible lorsque la charge de la génératrice comporte surtout des moteurs.
Entrez la longueur simple du conducteur en pieds entre la source de la génératrice et l'équipement raccordé.
Activez cette option pour obtenir une évaluation de planification à 125% correspondant à une charge soutenue de la génératrice, plutôt qu'une simple vérification selon la plaque signalétique.
12 kW at 240 V, single-phase, PF 1.00
115% minimum generator-output conductor screen per NEC 445.13.
21.1 mm² equivalent, 70.0 A ampacity screen, 2.31 V estimated drop (0.96%).
Chaque ligne compare le matériau du conducteur et la température nominale des bornes sélectionnés à l'intensité admissible requise ainsi qu'à la chute de tension estimée pour la longueur de parcours saisie.
| Calibre | Intensité admissible | Résistance | Chute de tension | État |
|---|---|---|---|---|
14 AWG 2.1 mm² | 15.0 A | 3.0700 ohm/kft | 23.0 V / 9.59% | Augmenter le calibre |
12 AWG 3.3 mm² | 20.0 A | 1.9300 ohm/kft | 14.5 V / 6.03% | Augmenter le calibre |
10 AWG 5.3 mm² | 30.0 A | 1.2100 ohm/kft | 9.07 V / 3.78% | Augmenter le calibre |
8 AWG 8.4 mm² | 40.0 A | 0.7640 ohm/kft | 5.73 V / 2.39% | Augmenter le calibre |
6 AWG 13.3 mm² | 55.0 A | 0.4910 ohm/kft | 3.68 V / 1.53% | Augmenter le calibre |
4 AWG 21.1 mm² | 70.0 A | 0.3080 ohm/kft | 2.31 V / 0.96% | Conforme |
3 AWG 26.7 mm² | 85.0 A | 0.2450 ohm/kft | 1.84 V / 0.77% | Conforme |
2 AWG 33.6 mm² | 95.0 A | 0.1940 ohm/kft | 1.46 V / 0.61% | Conforme |
1 AWG 42.4 mm² | 110 A | 0.1540 ohm/kft | 1.16 V / 0.48% | Conforme |
1/0 AWG 53.5 mm² | 125 A | 0.1220 ohm/kft | 0.91 V / 0.38% | Conforme |
2/0 AWG 67.4 mm² | 145 A | 0.0967 ohm/kft | 0.73 V / 0.30% | Conforme |
3/0 AWG 85.0 mm² | 165 A | 0.0766 ohm/kft | 0.57 V / 0.24% | Conforme |
4/0 AWG 107.2 mm² | 195 A | 0.0608 ohm/kft | 0.46 V / 0.19% | Conforme |
250 kcmil 126.7 mm² | 215 A | 0.0515 ohm/kft | 0.39 V / 0.16% | Conforme |
300 kcmil 152.0 mm² | 240 A | 0.0429 ohm/kft | 0.32 V / 0.13% | Conforme |
350 kcmil 177.3 mm² | 260 A | 0.0367 ohm/kft | 0.28 V / 0.11% | Conforme |
400 kcmil 202.7 mm² | 280 A | 0.0321 ohm/kft | 0.24 V / 0.10% | Conforme |
500 kcmil 253.3 mm² | 320 A | 0.0258 ohm/kft | 0.19 V / 0.08% | Conforme |
Use this calculator for fixed wiring between a generator, inlet, transfer switch, disconnect, or downstream distribution equipment. If you are sizing a portable cord set instead, use the extension cord tool and verify the cord listing.
- Les conducteurs d'artère de génératrice doivent tout de même faire l'objet d'une revue finale portant sur la protection contre les surintensités, l'homologation de l'appareillage de transfert et toute règle de neutre ou de mise à la terre applicable à l'installation.
- Les limites de chute de tension présentées ici sont des cibles de planification et non des exigences directes du NEC. Les équipements sensibles et le démarrage des moteurs justifient souvent une limite de chute plus stricte.
- Cet outil s'applique au câblage fixe entre une génératrice et l'équipement en aval, et non aux cordons souples portatifs ni aux approbations de câblage temporaire.
7.5 kW portable generator to 30A inlet
At 240 V single-phase and 60 ft one way, the calculated current is about 31.3 A. 10 AWG copper has enough ampacity but usually pushes above a tight 2% drop limit, so 8 AWG becomes the cleaner fixed-wiring choice.
20 kW standby generator to transfer switch
A 20 kW, 120/240 V single-phase unit delivers about 83.3 A at PF 1.00. With a 100 ft run and 3% target, 3 AWG copper can be a practical planning result before final OCPD, neutral sizing, and grounding checks.
60 kW three-phase generator feeder
On 480 V three-phase at PF 0.9, load current is roughly 80 A. Voltage drop is modest at this voltage, so the selection is often driven by ampacity, terminals, and installation conditions rather than distance alone.
Voltage Drop Calculator
Run a broader AC voltage-drop check after the generator circuit layout is known.
Ampacity Calculator
Review terminal temperature, bundling, and derating before final conductor release.
Conduit Fill Calculator
Check raceway occupancy once phase, neutral, and grounding conductors are selected.
Cable Size Calculator
Compare the generator feeder result with a broader residential or commercial sizing workflow.
Wire Resistance Calculator
Audit raw conductor resistance if you want to inspect the voltage-drop math directly.
Wire Weight Calculator
Estimate pull weight and reel handling for larger standby generator feeders.