발전기 전선 크기 계산기
// 발전기 입구, 전환 스위치 및 대기 배전을 위한 예비 검토 피더 도체 크기는 KW, 전압, 거리 및 낙하 목표에 따라 결정됩니다. //
1차 통과 도체 화면의 경우 발전기 명판 실제 전력 출력을 킬로와트로 입력합니다.
실제 발전기 출력 또는 피더 전압을 선택하여 전류 및 강하가 올바른 기준으로 확인되도록 하십시오.
저항성 또는 명판 kW 계획에는 1.00를 사용하고, 발전기 부하에 모터가 많은 경우에는 더 낮은 PF를 입력하십시오.
발전기 소스와 연결된 장비 사이의 단방향 도체 길이를 피트 단위로 입력합니다.
직접적인 명판 확인 대신 지속적인 발전기 부하를 위한 125% 계획 화면을 원할 때 이 기능을 활성화하십시오.
12 kW at 240 V, single-phase, PF 1.00
115% minimum generator-output conductor screen per NEC 445.13.
21.1 mm² equivalent, 70.0 A ampacity screen, 2.31 V estimated drop (0.96%).
각 행에서는 입력된 배선 길이에 대해 필요한 허용전류 및 예상 전압강하와 비교하여 선택한 도체 재질 및 단자 정격을 확인합니다.
| 크기 | 허용전류 | 저항 | 전압강하 | 상태 |
|---|---|---|---|---|
14 AWG 2.1 mm² | 15.0 A | 3.0700 ohm/kft | 23.0 V / 9.59% | 크기 확대 |
12 AWG 3.3 mm² | 20.0 A | 1.9300 ohm/kft | 14.5 V / 6.03% | 크기 확대 |
10 AWG 5.3 mm² | 30.0 A | 1.2100 ohm/kft | 9.07 V / 3.78% | 크기 확대 |
8 AWG 8.4 mm² | 40.0 A | 0.7640 ohm/kft | 5.73 V / 2.39% | 크기 확대 |
6 AWG 13.3 mm² | 55.0 A | 0.4910 ohm/kft | 3.68 V / 1.53% | 크기 확대 |
4 AWG 21.1 mm² | 70.0 A | 0.3080 ohm/kft | 2.31 V / 0.96% | 통과하다 |
3 AWG 26.7 mm² | 85.0 A | 0.2450 ohm/kft | 1.84 V / 0.77% | 통과하다 |
2 AWG 33.6 mm² | 95.0 A | 0.1940 ohm/kft | 1.46 V / 0.61% | 통과하다 |
1 AWG 42.4 mm² | 110 A | 0.1540 ohm/kft | 1.16 V / 0.48% | 통과하다 |
1/0 AWG 53.5 mm² | 125 A | 0.1220 ohm/kft | 0.91 V / 0.38% | 통과하다 |
2/0 AWG 67.4 mm² | 145 A | 0.0967 ohm/kft | 0.73 V / 0.30% | 통과하다 |
3/0 AWG 85.0 mm² | 165 A | 0.0766 ohm/kft | 0.57 V / 0.24% | 통과하다 |
4/0 AWG 107.2 mm² | 195 A | 0.0608 ohm/kft | 0.46 V / 0.19% | 통과하다 |
250 kcmil 126.7 mm² | 215 A | 0.0515 ohm/kft | 0.39 V / 0.16% | 통과하다 |
300 kcmil 152.0 mm² | 240 A | 0.0429 ohm/kft | 0.32 V / 0.13% | 통과하다 |
350 kcmil 177.3 mm² | 260 A | 0.0367 ohm/kft | 0.28 V / 0.11% | 통과하다 |
400 kcmil 202.7 mm² | 280 A | 0.0321 ohm/kft | 0.24 V / 0.10% | 통과하다 |
500 kcmil 253.3 mm² | 320 A | 0.0258 ohm/kft | 0.19 V / 0.08% | 통과하다 |
Use this calculator for fixed wiring between a generator, inlet, transfer switch, disconnect, or downstream distribution equipment. If you are sizing a portable cord set instead, use the extension cord tool and verify the cord listing.
- 발전기 급전선 도체에는 과전류 보호, 전송 장비 목록 및 설치에 적용되는 중성선 또는 접지 규칙에 대한 최종 검토가 여전히 필요합니다.
- 여기서 전압강하 제한은 직접적인 NEC 명령이 아닌 계획 목표입니다. 민감한 장비와 모터 시동은 종종 더 엄격한 낙하 제한을 정당화합니다.
- 이 도구는 발전기와 하위 장비 사이의 고정 배선용이며 유연한 휴대용 코드 세트 또는 임시 배선 승인용이 아닙니다.
7.5 kW portable generator to 30A inlet
At 240 V single-phase and 60 ft one way, the calculated current is about 31.3 A. 10 AWG copper has enough ampacity but usually pushes above a tight 2% drop limit, so 8 AWG becomes the cleaner fixed-wiring choice.
20 kW standby generator to transfer switch
A 20 kW, 120/240 V single-phase unit delivers about 83.3 A at PF 1.00. With a 100 ft run and 3% target, 3 AWG copper can be a practical planning result before final OCPD, neutral sizing, and grounding checks.
60 kW three-phase generator feeder
On 480 V three-phase at PF 0.9, load current is roughly 80 A. Voltage drop is modest at this voltage, so the selection is often driven by ampacity, terminals, and installation conditions rather than distance alone.
Voltage Drop Calculator
Run a broader AC voltage-drop check after the generator circuit layout is known.
Ampacity Calculator
Review terminal temperature, bundling, and derating before final conductor release.
Conduit Fill Calculator
Check raceway occupancy once phase, neutral, and grounding conductors are selected.
Cable Size Calculator
Compare the generator feeder result with a broader residential or commercial sizing workflow.
Wire Resistance Calculator
Audit raw conductor resistance if you want to inspect the voltage-drop math directly.
Wire Weight Calculator
Estimate pull weight and reel handling for larger standby generator feeders.